Pro-face LT Series Installationsanleitung

/77070,QVWDOODWLRQ*XLGH/77070਄ඞହ৥છ

LT-4201TM/4301TM10EnglishDisplay Module/Rear Module Separation Cable RangeAgency Certifications for LT UnitFor information on Standards and Regulation

LT-4201TM/4301TM Installation Guide11EnglishInterfaces are: COM1, Ethernet, USB1 and USB2.CAUTIONENVIRONMENTAL HAZARDS TO THE EQUIPMENT Allow the dev

LT-4201TM/4301TM12EnglishPackage ContentsVerify that all items shown in the figure are present in your package:Legend Description Package TypeLT Unit

LT-4201TM/4301TM Installation Guide13EnglishHandling the LCDIf the Panel is damaged and any liquid comes in contact with your skin, immediately rinse

LT-4201TM/4301TM14EnglishLT-4201TM/4301TM and Rear Module Parts Identification:Part DescriptionA Display moduleB Rear moduleC USB (type A) interface c

15LT-4201TM/4301TM Installation GuideEnglishLT-4201T M/4301TM Installa tion Guide Installati onInstallationInserting the Display Module with an Anti-

16EnglishInstalling the LT DisplayThe figure shows the assembly:(1) Display module(2) Panel(3) Display installation nut(4) Anti-rotation teeInstal

LT-4201TM/4301TM Installation Guide17EnglishThe figure shows the assembly with the Panel spacer:(1) Display module(2) Panel(3) Spacer(4) Display

18EnglishIf you power up the rear module without connecting the display module, the logic controller does not start and all outputs remain in the init

LT-4201TM/4301TM Installation Guide19EnglishSetup ProcedureMount the unit in an enclosure that provides a clean, dry, robust, and controlled environme

2English The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the produ

20English The panel face is not inclined more than 30° when installing the unit in a slanted panel:  The power plug is positioned vertically when t

LT-4201TM/4301TM Installation Guide21EnglishThe figure shows how to install the panel with the rear module:1 Create the correct sized holes required

22EnglishCorrect Mounting PositionThe rear module must be mounted with steel sheet horizontally or vertically plane as shown in the figure: NOTE: Keep

LT-4201TM/4301TM Installation Guide23EnglishIncorrect Mounting PositionThe rear module should only be positioned in correct mounting position to help

24EnglishThe figure shows the minimum clearance for the rear module:Installing the Rear Module on a DIN RailThe following procedure describes how to i

LT-4201TM/4301TM Installation Guide25EnglishRemoving the Rear Module from a DIN RailThe following procedure describes how to remove the rear module fr

26English

27LT-4201TM/4301TM Installation GuideEnglishLT-4201T M/4301TM Installa tion Guide Wiring PrinciplesWiring PrinciplesWiring Rules and RecommendationsT

28English1Multipoint grounding is permissible if connections are made to an equipotential ground plane dimensioned to help avoid shielded cable damage

LT-4201TM/4301TM Installation Guide29EnglishAvoid temperature changes on the thermocouple’s connection terminal. Temperature measurements may not be a

3LT-4201TM/4301TM Installation Guide!EnglishSafety InformationImportant InformationNOTICERead these instructions carefully, and look at the equipment

30EnglishAlso, the screwdriver tip must be flat, as indicated, to access the narrow hole of the terminal block:The terminal blocks are a spring clamp

LT-4201TM/4301TM Installation Guide31English(3) Do not rotate the point of the screwdriver inside the square-shaped opening. It may damage the equipme

32EnglishThe figure shows the groups and the signal names of the terminal blocks:The figure shows the groups and the signal names of the terminal bloc

LT-4201TM/4301TM Installation Guide33EnglishThe figure shows the pin assignment of the LT-4201TM (Modular Type Analog), LT-4301TM (Modular Type Analog

34EnglishThe figure shows the group and the signal names of the terminal blocks:Connecting the Power CordFollow these instructions when supplying powe

LT-4201TM/4301TM Installation Guide35EnglishPower Cord PreparationBefore using your power cord:  Verify that the ground wire is the same gauge or hea

36EnglishNOTE:  Do not solder the wire directly to the power receptacle pin. The power supply cord must meet the specification shown above. Twist th

LT-4201TM/4301TM Installation Guide37EnglishPower Supply ConnectionsFor maintenance purpose, use the following connection diagram to set up your power

38EnglishThe diagram illustrates a lightning surge absorber connection:Grounding the SystemTo minimize the effects of electromagnetic interference, ca

LT-4201TM/4301TM Installation Guide39EnglishFunctional Ground on the DIN RailThe DIN rail for your LT system is common with the functional ground plan

4EnglishPLEASE NOTEElectrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assu

40EnglishProtective Earth Ground (PE) Cable ShieldingThe following shows the steps when using shield cables for grounding the LT power supply, Standar

LT-4201TM/4301TM Installation Guide41EnglishCommon GroundingIf exclusive grounding is not possible, use a common grounding point. Use grounding resist

42English

43LT-4201TM/4301TM Installation GuideEnglishLT-4201T M/4301TM Installa tion GuideCommunication Interfaces Communicati on InterfacesCommunication Inte

Communication Interfaces44EnglishAttaching and Removing the USB Mini-B Holder1 USB holder2 USB cableNOTE: The USB holder is supplied in the accessor

LT-4201TM/4301TM Installation Guide45EnglishSerial Interface Pin Assignment COM1The figure shows the pins of the RJ45 connector when viewed from LT:Th

Communication Interfaces46EnglishAlthough LT does not restrict you from doing so, we recommend that you not exceed 16 CANopen slave modules (and/or 32

LT-4201TM/4301TM Installation Guide47EnglishSystem LED DisplayNOTE:  Ethernet LEDs are mounted next to the I/O terminal block. CANopen LED is mounte

5LT-4201TM/4301TM Installation GuideEnglishAbout the BookDocument ScopeThank you for purchasing Pro-face's LT4000 Series Graphic Logic Controller

6EnglishProduct Related InformationThis equipment has been designed to operate outside of any hazardous location. Only install this equipment in zones

LT-4201TM/4301TM Installation Guide7English1 For additional information, refer to NEMA ICS 1.1 (latest edition), "Safety Guidelines for the Appli

8English

9LT-4201TM/4301TM Installation GuideEnglishLT-4201T M/4301TM Installa tion GuideLT-4201T M/4301TM LT-4201T M/4301TM of Panel sLT-4201TM/4301TM of Pa