Pro-face GP577R-TC11 Bedienungsanleitung

Easy! Smooth! GP-577R Series→GP4000 Series Replacement Guidebook 1/48 Second Edition Mar. 2012 Copyright © 2012.3 Digital Electronics Corporation.

Chapter 2 Compatibility of Hardware 2.1 Locations of connector Connector locations on GP-577RT/S and GP-4501T/TW are as follows; GP-577RT/S GP-4501

Interface names GP-577RT/S GP-4501T GP-4501TW 1 Power Input Terminal Block (AC/DC type) Power Input Terminal Block (AC type)/ Power Connector (DC

2.2 Touch Panel specifications 2.2.1 When replacing GP-577RT/S with GP-4501T You can select the Matrix type (2-point touch input at the same time same

2.4 Transfer cable To transfer screen data to GP-4501T/TW, use a USB transfer cable or Ethernet. The USB cables that can be used for GP-4501T/TW are a

2.5.3 CF Card Interface (only when using “Multi Unit” (GP077-MLTS11, GP077-MLTE41)) GP-4501T/TW is not equipped with a CF card slot. But a SD card slo

2.6.2 Printer connection GP-4501T/TW is not equipped with Centronics (parallel) Interface for a printer though GP-577RT/S is equipped with it. If the

2.8 Backup Battery Unlike GP-577RT/S, GP-4501T/TW does not use rechargeable secondary batteries but replaceable primary ones. (For both a rechargeable

Chapter 3 Replacement Procedure 3.1 Work Flow ow Receive screen data from GP-577RT/S. *1 C

3.2 Preparation PC in which GP-PRO/PBIII for Windows V2.1 or later is installed. *2 Requirements for receiving screen data from GP-577RT/S *1 Transfe

3.3 Receive screen data from GP-577RT/S This section explains, as an example, how to receive screen data from GP-577RT/S using a transfer cable, GPW-C

Preface This manual introduces the procedures to replace a GP-577RT/S unit with a unit in GP-4501T/TW. Model in use Recommended Substitution GP-4

(4) In the Communication Port field, select [COM], specify the COM port to which the cable is connected, and click [OK]. If you use a USB transfer

(5) Select the [Transfer] menu and click [Receive...]. (6) Specify the location to save the received screen data at and the project file name and sa

In case there is no Upload Information “Upload Information” is necessary to receive screen data from GP-577RT/S. It needs to be included in screen dat

3.4 Convert screen data with the Project Converter Convert a project file (*.prw) for GP-577RT/S with the GP-Pro EX’s Project Converter. (1) Click th

(4) In [Convert-To], designate a GP-Pro EX’s project file (*.prx). Click the [Browse…] button and enter a new [File Name] (e.g.: “Product system

NOTE When a convert-to file exists, the window that confirms whether or not to overwrite the file is displayed. 25/48

(5) Click [Convert] and start the conversion. (6) If you are asked about the [Convert-To] type as shown below, select [GP-4501T] on the pull-down me

If an error message is displayed during conversion… If an error message is displayed during conversion, refer to [Project Converter Error Message] (

(7) After conversion, the [Save convert information] dialog box appears. If you click [Save], you can save the conversion information in a CSV file fo

Convert GP-PRO/PBIII for Windows “Destination CF Card Folder” If you convert a project file (*.prw) with a destination CF card folder designated in th

GP4000 Series Model Number GP4000 series model number partly differs depending on a specification. Before placing an order, please make sure of the m

3.5 Change the Display Unit Type (only when replacing with GP-4501TW) Open the project file (*.prx) on GP-Pro EX that is converted in the Chapter 3.4

(1) Connect your PC and GP-4501T/TW with a USB transfer cable (model: CA3-USBCB-01). If the driver of the cable has not been installed on you PC yet,

(2) Trun on the power of GP-4501T/TW. The “Initial Start Mode” screen will appear on the display unit. After transferring a project file once, this sc

(4) Make sure that the [Device] in the “Transfer Settings Information” is set to [USB]. If not, click the [Transfer Setting] button to open the “Trans

(7) When transfer is completed, the status displayed in the dialog box will change from [Transferring] to [Complete Transfer]. Click [Close] to close

3.7 Differences of software 3.7.1 Differences after conversion Check the differences of screen data after conversion from GP-PRO/PBIII to GP-Pro EX. F

25 Compatibility of Ladder Monitor 26 Compatibility of J Tag and R Tag 27 Converting Screen Data of DOS 28 Compatibility of Standard Font 29 D Sc

Chapter 4 Communication with Device/PLC 4.1 Driver list More connectable drivers will be added. For the devices/PLC each driver supports, see [Connec

4.2 Shapes of COM ports GP-577RT/S GP-4501T/TW D-Sub 25 pin (socket) RS-232C/422 D-Sub 9 pin (plug) RS-232C COM1 D-Sub 9 pin (plug) RS-422/485

4.3 Signals of COM ports 4.3.1 Signals of COM1 For GP-577RT/S RS-232C or RS-422 (socket) 39/48

Contents PREFACE 2 GP4000 SERIES MODEL NUMBER 3 CONTENTS 4 CHAPTER 1 SPECIFICATION COMPARISON 6 1.1 SPECIFICATIONS OF GP-577RT/S AND GP-4501T 6 1.2

For GP-4501T/TW RS-232C (plug) *1: RI and VICC of Pin 9 are switched on the software. VCC Output is not protected from overcurrent. Please fo

4.3.2 Signals of COM2 For GP-577RT/S None For GP-4501T/TW RS-422/485 (plug) 4.4 Multilink Connection For GP-4501T/TW, some communication drivers

4.5 Cable Diagram at the time of replacement The connection cable for GP-577RT/S can be used for GP-4501T/TW. But please note that there are precautio

4.5.1 When using a RS-232C connection cable GP-577RT/S System Configuration (connecting to COM1) GP-4501T/TW System Configuration (connecting to COM

4.5.2 When using a RS-422 connection cable GP-577RT/S System Configuration (connecting to COM1) GP-4501T/TW System Configuration (connecting to COM2

NOTE When using a terminal block adapter (GP070-CN10-O), we recommend you to replace it with a terminal block conversion adapter (PFXZCBADTM1) for GP-

Chapter 5 Appendix 5.1 Changing the setting of the external media to use If a CF card is used for GP-PRO/PBIII, after GP-577RT/S is replaced with GP-4

[Solution] 1. Change the SD Card setting to the USB storage setting following the steps below. <Procedure> i. Click [Project]->[Informati

NOTE ・ To see how the tags or the parts of GP-PRO/PBIII for Windows are replaced on GP-Pro EX, refer to [OtasukePro!] “Feature Comparison between GP-P

5/48 2.7.2 DC POWER SUPPLY TYPE 15 2.8 BACKUP BATTERY 16 2.9 POWER CONSUMPTION 16 2.10 MATERIALS/COLORS OF THE BODY 16 CHAPTER 3 REPLACEMENT PROCED

Chapter 1 Specification Comparison 1.1 Specifications of GP-577RT/S and GP-4501T GP-577RT/S GP-4501T GP-577RT TFT color LCD Display Type GP-577R

SD Card I/F - NEW! ✔ Type A USB I/F Type mini B - NEW! ✔ →See 2.4 Tool Connector I/F ✔ - Printer I/F Centronic-compliant (parallel) NEW! USB (Type A)

1.2 Specifications of GP577RT/S and GP-4501TW GP-577RT/S GP-4501TW GP-577RT TFT color LCD Display Type GP-577RS STN color LCD TFT color LCD GP-

Type A USB I/F Type mini B - NEW! ✔ →See 2.4 Tool Connector I/F ✔ - Printer I/F Centronic-compliant (parallel) NEW! USB (Type A) →See 2.6.2 Auxiliary